The full guide to the Kretrum 32-colour Start refills
This is a third-party refill pack for the 3Doodler Start family: 32 colours of low-temperature PCL in 15 cm strands, glow-in-the-dark shades included, in a resealable pack. It is for families whose child already draws with a Start or Start+ and wants more colours than the pen came with. The trade-off is the warranty: 3Doodler says using third-party filament in the Start+ voids any active warranty, so timing matters.
Key specifications
| Material | PCL, low printing temperature |
|---|---|
| Diameter | About 2.5 mm |
| Colours | 32, including glow-in-the-dark |
| Strand length | 15 cm |
| Strands per colour | Not confirmed by an official source; check the listing |
| Fits | 3Doodler Start and Start+ only, according to the seller |
| Packaging | Resealable |
Read this before you buy: compatibility and warranty
Three facts decide whether this pack is right for your pen:
- It won’t fit standard pens. These are thick, low-temperature strands. Pens built for 1.75 mm PLA or ABS, such as the SCRIB3D P1, the MYNT3D Super or the 3Doodler Flow, can’t use them.
- The seller says it fits the Start and Start+. The only Start-family pen we list is the 3Doodler Start+ Essentials set, which takes Start plastic only, not 1.75 mm PLA.
- 3Doodler doesn’t approve it. 3Doodler’s FAQ says the Start+ is designed to work with its own Start+ Eco-Filament, developed for the pen’s lower temperatures, and that using third-party filament voids any active warranty.
Our rule of thumb: while the pen is under warranty, stay with 3Doodler’s own Start plastic. Once the warranty has ended, or if you accept the risk, this pack is a way to add colours, including glow-in-the-dark.
Who it suits — and who should pick something else
- Suits: owners of a Start or Start+ whose warranty has ended, children who want more colours for animals and models, and anyone planning glow-in-the-dark projects.
- Pick something else: if your pen takes 1.75 mm filament, choose a PLA pack instead, such as the Yungden 30-colour PLA refills. If your Start+ is still under warranty, choose 3Doodler’s own Start+ Eco-Filament.
Still deciding on a first pen for a young child? Our Start+ and SCRIB3D P1 comparison sets out the differences, and our ranked list of 3D pens covers every pen we list.
What’s in the box
Strands of low-temperature PCL in 32 colours, including glow-in-the-dark, each 15 cm long, in resealable packaging. No pen is included.
How to use it in a Start+
3Doodler’s own guidance for the Start+ applies to any strand you feed it:
- Charge the pen fully before a session. 3Doodler gives 30 minutes to an hour, with the pen switched off while it charges.
- Switch on and wait for the light to turn from red to green. 3Doodler says this takes about 30 seconds and can take up to two minutes.
- Push a strand into the feeding port at the back while the pen feeds forward, then start drawing.
- When a strand runs low, extrusion can slow. 3Doodler’s advice is to put the next strand in behind it and give it a gentle nudge.
- If a strand won’t grip, push it firmly into the port while the pen feeds forward. For a strand stuck at the back, 3Doodler suggests pushing while twisting the pen by 90°.
Left switched on without drawing, the pen goes into standby after a few minutes; a single click wakes it. If a third-party strand keeps jamming, stop and go back to 3Doodler’s own plastic rather than forcing it.
Getting the most from 32 colours
With 15 cm strands, every colour change is a fresh strand, which makes swapping easy for small hands. Sort the strands by colour into the resealable pack, and hand a child three or four colours per project rather than the whole set. The glow-in-the-dark strands work best on details that will be seen with the lights off: eyes, moons on a mobile, the outline of a ghost. Our guide to glow-in-the-dark pen filament covers how to charge and show them off. Drawing flat on our printable 3D pen templates helps young children keep lines tidy.
Storage is simple: 3Doodler recommends keeping pen filament in a cool, dry, dark place, so close the pack after each session. Because PCL is a low-temperature plastic, keep finished models away from radiators and sunny windowsills.
How it compares
- Kretrum 32-Colour Refills for 3Doodler Start: PCL, about 2.5 mm, 15 cm strands, 32 colours including glow-in-the-dark; third-party.
- 3Doodler Start+ Essentials (strands in the box): 72 strands of 3Doodler Start Eco-Filament with the pen, according to 3Doodler UK; the filament 3Doodler designs the pen around.
- Yungden 30-Colour PLA Refills: 1.75 mm PLA for hot pens; does not fit the Start family.
For how PCL differs from PLA and ABS, see our guide to 3D pen filament types.
Common questions
Will Kretrum refills void the 3Doodler Start+ warranty?
3Doodler’s FAQ says the use of third-party filament in the Start+ voids any active warranty. If your pen is still covered, use 3Doodler’s own Start+ Eco-Filament until the warranty ends.
Do these refills fit a normal 1.75 mm 3D pen?
No. They are thicker, low-temperature strands sold for the 3Doodler Start family only. A pen that takes 1.75 mm PLA needs a PLA refill pack.
Are these the same plastic as 3Doodler’s own Start strands?
Not necessarily. Kretrum describes its strands as PCL; 3Doodler describes its Start+ Eco-Filament as a low-temperature plastic developed for the pen. The seller’s compatibility claim is not an endorsement from 3Doodler.
What age are they for?
Follow the pen’s rating. 3Doodler UK designs the Start+ for children aged 6 to 13, and says the pen has no external hot parts. 3Doodler also recommends a well-ventilated room for all its filaments.
How do the glow-in-the-dark strands work?
Like other glow plastics, they need light to charge before they glow. Draw the glowing parts last, on top, so they aren’t hidden under other colours.
Specifications as published by Kretrum on its official listing, checked November 2026. Where a figure isn’t published, we say so.


