3D Pen Guides

3Doodler Start+ vs SCRIB3D P1: Which Pen for a Young Child?

One pen has no external hot parts, according to 3Doodler, and is designed for ages 6 to 13; the other melts PLA in a hot nozzle and is rated from 14. Specs, refills and a clear rule for choosing.

3Doodler Start+ vs SCRIB3D P1: Which Pen for a Young Child?
Heads up: we research and compare the products we recommend, and we only link to gear we would consider buying ourselves. When you buy through links on this page we may earn a commission, at no extra cost to you. As an Amazon Associate we earn from qualifying purchases.
On this page
  1. 3Doodler Start+ vs SCRIB3D P1: specs side by side
  2. Safety: no external hot parts against a hot ceramic nozzle
  3. What each pen can make
  4. Refills: 2.5 mm Start plastic against standard 1.75 mm PLA
  5. Who should choose which
  6. Can a child move from the Start+ to the P1 later?
  7. Common questions
  8. Sources
Short answer

For a young child, buy the 3Doodler Start+. 3Doodler says it has no external hot parts and rates it for ages 6 to 13. The SCRIB3D P1 melts PLA or ABS in a hot ceramic nozzle: SCRIB3D’s product page rates it for 14 and over, and its manual says adult use only, so keep it for later.

These two pens look like rivals, but they’re different tools. The 3Doodler Start+ is a play pen with no external hot parts, according to 3Doodler, built around its own low-temperature plastic. The SCRIB3D P1 is a hot pen for building in standard PLA and ABS. Which one suits your child comes down to two things: their age, and how closely an adult will be watching.

  • Choose the Start+ for a child aged 6 to 13, especially under ten.
  • Choose the P1 for a teenager of 14 or more who wants firmer models, with an adult in the room.
  • Choose neither yet for a child under six: no pen here is rated that young.

3Doodler Start+ vs SCRIB3D P1: specs side by side

The figures come from the makers’ own pages, the P1 manual and the product listings. Where a maker publishes nothing, the table says so.

Spec 3Doodler Start+ SCRIB3D P1
Maker’s age rating 6 to 13 14 and over on SCRIB3D’s product page; the manual says adult use only
Hot parts None external, according to 3Doodler Ceramic nozzle that gets hot
Plastic it takes 3Doodler Start plastic, or a compatible 2.5 mm pack PLA and ABS, 1.75 mm
Published temperature None published PLA 160–210 °C; ABS 210–235 °C on the listing, 200–230 °C in the manual
Controls One click starts and stops the flow LCD screen, temperature buttons, stepless speed slider, forward and reverse
Warm-up About 30 seconds, according to 3Doodler Not published; a light turns from red to green when ready
Power Rechargeable, charging cable included; up to 45 minutes of continuous drawing, or 1 to 1.5 hours stop-start, on 3Doodler’s Start+ page; its help centre says about 30–45 minutes 5 V 2 A power adapter, or a power bank with at least 2 A output
Stand-by Stand-by mode Sleeps after 2 minutes without use on the listing, 5 minutes in the manual
In the box Pen, charging cable, 72 strands of Start eco-filament, activity guide, according to 3Doodler UK Pen, 3 colours of PLA (30 ft, about 9 m), power adapter, manual, stencil guide

Two rows carry two figures each, because SCRIB3D’s manual gives a lower ABS range and a longer sleep delay than the listing. In practice, follow the manual that comes in your box and the temperature shown on the pen’s own screen.

Safety: no external hot parts against a hot ceramic nozzle

This is the difference that decides it for most parents. 3Doodler says the Start+ has no external hot parts. The P1 works the other way: it pushes plastic through a ceramic nozzle at 160–210 °C for PLA.

SCRIB3D’s manual is blunt about what that means. It tells you not to touch the nozzle, to keep it away from anything flammable, to warn others nearby that the pen is hot, and to let the nozzle cool completely before you put the pen away. Its warning box reads: “Adult use only. Keep out of reach of children.” The product page sets the age at 14 and over, so a teenager can use it, but treat it as a tool that needs an adult close by.

ABS adds a second risk. The manual warns that ABS can expose you and others in the room to styrene, and says to use the pen in a well-ventilated area. We’d keep teenagers on PLA and leave ABS to adults.

The Start+ has its own small rule: 3Doodler says not to use it while it’s charging. For burns, supervision and house rules in general, see our guide to 3D pen safety for children.

What each pen can make

Both draw in the air, but the plastic they use sets what a model can be.

The Start+: play pieces and simple figures

3Doodler says its Start plastic extrudes and hardens quickly. It also stays softer than PLA once it sets, so it suits toys, simple figures and flat shapes lifted into 3D more than fine detail. Think of it as a modelling toy more than a building tool.

The single-click control is the other strength. There’s no temperature to choose and no setting to get wrong, and the pen works away from a socket. On a full charge, it runs for up to 45 minutes of continuous drawing according to 3Doodler’s Start+ page, or about 30–45 minutes according to its help centre. Either way, that’s a long session for a six-year-old.

The P1: firmer models and finer control

The P1 draws in 1.75 mm PLA and ABS. SCRIB3D pitches it at simple hobby projects and personalised gifts. PLA sets firmer than Start plastic, which suits models with more structure and crisper edges.

Its controls reward patience. The stepless slider lets you slow down for corners and upright lines and speed up to fill a shape, and the screen shows the set and actual temperature. SCRIB3D’s manual adds two tips: for flat drawing, hold the pen at 65° or steeper, and if the plastic bubbles or crackles, lower the temperature by 5–10 °C.

Refills: 2.5 mm Start plastic against standard 1.75 mm PLA

You buy the pen once and the plastic many times over. The two systems don’t cross over: 1.75 mm PLA won’t fit the Start+, and 2.5 mm Start strands won’t fit the P1.

Refill For What you get
3Doodler Start+ Eco-Refills Start and Start+ only Packs of 75 or 250 strands; non-toxic and BPA-free, according to 3Doodler
Kretrum 32-Colour Refills for 3Doodler Start Start and Start+ only, according to the seller 32 colours of about 2.5 mm PCL in 15 cm strands, glow-in-the-dark included
SCRIB3D PLA Refills SCRIB3D P1 and most 1.75 mm PLA pens 20 colours, about 100 m in total, 160–210 °C, each colour vacuum packed
Yungden 30-Colour PLA Refills Standard 1.75 mm hot pens 30 colours, 3 m each, 90 m in total, 180–210 °C

For the Start+

3Doodler says its Eco-Refills are designed for the Start+ and may not suit other pens. Store them somewhere cool and dry, out of direct sunlight, which 3Doodler says stops them warping. For more colours, the Kretrum 32-colour Start refills are low-temperature PCL in a resealable pack. They’re a third-party refill, so 3Doodler’s own plastic remains the surest choice if you’re unsure.

For the P1

The P1 takes standard 1.75 mm PLA, but SCRIB3D’s manual ties the warranty to SCRIB3D-approved filament. While the warranty runs, the SCRIB3D PLA Refills are the safer choice, and they publish the same 160–210 °C range as the pen’s PLA mode. Once it has run out, the Yungden 30-colour PLA pack adds more colours and lists 180–210 °C, inside the P1’s PLA range. Whichever you buy, snip the end flat before you load a new strand: SCRIB3D’s manual says an angled or swollen end can jam the pen.

Who should choose which

Start with the age on the box, then decide who will be nearby.

If your child is… Choose Why
Under 6 Neither yet Neither maker rates its pen this young
6 to 9 3Doodler Start+ No external hot parts and one-click control
10 to 13 3Doodler Start+ The P1’s rating starts at 14
14 or over SCRIB3D P1, with an adult nearby Firmer PLA models and finer control

Buy the 3Doodler Start+ if your child is under 14

It’s the only one of the two its maker rates for a young child, and the only one with no external hot parts, according to 3Doodler. With no cord, it also goes wherever your child draws.

Who should skip it: a child who wants crisp detail or rigid models, and a family hoping to share refills with a 3D printer.

3Doodler Start+ Essentials 3D Pen Set
Our pick for ages 6 to 13
3Doodler Start+ Essentials 3D Pen Set

3Doodler says it has no external hot parts and designs it for ages 6 to 13. The pen to start with.

Check price on Amazon Price shown on Amazon

Buy the SCRIB3D P1 for a teenager of 14 or over

A teenager who has outgrown soft plastic gets rigid PLA, a stepless speed slider and a screen that shows the temperature. Keep them on PLA, put a heat-rated mat on the table, and stay in the room.

Who should skip it: anyone under 14, and any teenager set on ABS. We’d leave ABS to adults, in a well-ventilated room.

SCRIB3D P1 3D Pen with Display
Our pick for 14 and over
SCRIB3D P1 3D Pen with Display

Published PLA and ABS temperature ranges and a stepless speed slider: room to grow for a teenager, used on PLA with an adult nearby.

Check price on Amazon Price shown on Amazon

If your child sits between the two, at 10 to 13 and bored of soft plastic, our age-by-age guide to kids’ pens covers a supervised PLA pen for that gap. To see how the P1 compares with the other pens we list, look it up in our ranked list of 3D pens.

Can a child move from the Start+ to the P1 later?

Yes. On the product pages the two ratings meet: 3Doodler covers 6 to 13, SCRIB3D starts at 14, though the P1 manual still asks for adult use. What carries over is the skill, not the kit.

  • Skills carry over. Tracing a stencil, building in layers and planning a model work the same way on both pens.
  • Refills don’t. Leftover Start strands won’t fit the P1, so finish them first.
  • Habits change. 3Doodler says the Start+ has no external hot parts. On the P1 they must never touch the nozzle, so go over the manual’s warnings together before the first session.
  • The cable comes back. The P1 has no built-in battery: it runs from its adapter or, according to the manual, a power bank of at least 2 A.

There’s no need to give the Start+ away. It stays the quicker pen for a short session, and a younger brother or sister can take it on.

Common questions


Can the 3Doodler Start+ use the same refills as the SCRIB3D P1?

No. The Start+ takes 3Doodler Start plastic or a compatible 2.5 mm pack, while the P1 takes 1.75 mm PLA and ABS. Neither refill fits the other pen, so buy plastic for the pen you choose.


Is the SCRIB3D P1 suitable for a ten-year-old?

Not by its maker’s rating. SCRIB3D’s product page says 14 and over, and the warnings in its manual say adult use only. For a child of ten, the Start+ is the one of these two its maker rates for that age.


How long does the 3Doodler Start+ battery last?

Up to 45 minutes of continuous drawing, or 1 to 1.5 hours stop-start, on 3Doodler’s Start+ page; its help centre says about 30–45 minutes. The pen shouldn’t be used while it’s charging, so charge it between sessions rather than during them.


Can the SCRIB3D P1 work without a plug socket?

Yes, with a power bank. Besides the supplied adapter, SCRIB3D’s manual says the pen can run from a third-party power bank with an output of at least 2 A.


Sources

The 3D Hub editorial team

We compare 3D pens and printers on the specifications their makers publish, and say plainly when a manufacturer doesn't publish a figure. We don't accept payment for placement, and no ranking here moves because of a commission rate.