3D Pen Projects

Mother’s Day with a 3D Pen: 10 Gifts Kids Can Make

Ten Mother's Day gifts children can make with a 3D pen, sorted by age and time, with the adult's job spelled out for each one.

Mother’s Day with a 3D Pen: 10 Gifts Kids Can Make
Heads up: we research and compare the products we recommend, and we only link to gear we would consider buying ourselves. When you buy through links on this page we may earn a commission, at no extra cost to you. As an Amazon Associate we earn from qualifying purchases.
On this page
  1. Which gift suits your child's age?
  2. Ten Mother's Day gifts, from easiest to most ambitious
  3. What you need
  4. Step outlines for three of the gifts
  5. When should you start?
  6. Common questions
  7. Sources

These ten gifts are sorted by the child’s age and by how long each one takes, from a card a six-year-old can finish in one sitting to a bouquet for a teenager with a hot pen. For each one we say what the child draws and what the adult does. Mothering Sunday moves every year, so check the date early.

Which gift suits your child’s age?

Children aged 6 to 13 can make the first seven gifts on a pen with no external hot parts; the last three need a hot pen and suit teenagers of 14 and up. 3Doodler designs the 3Doodler Start+ for ages 6 to 13 and says it has no external hot parts, so the first seven gifts are planned for it. SCRIB3D rates the SCRIB3D P1 for ages 14 and up on its product page (its user manual says adult use only), and it melts PLA at 160–210 °C, so the last three are for teenagers with an adult in the room.

Short means under half an hour, medium up to an hour, and long an afternoon or two sittings, cooling included. These bands are our estimates for planning, not timed figures, so leave some slack for a first go.

Gift Pen’s age rating Time Pen The adult’s job
1. Card with raised flowers 6 to 13 Short 3Doodler Start+ Prints the stencil, helps with the glue
2. Bookmark 6 to 13 Short 3Doodler Start+ Checks it lies flat in a book
3. Keyring tag 6 to 13 Short 3Doodler Start+ Fits the split ring
4. Fridge magnet 6 to 13 Short 3Doodler Start+ Glues on the magnet
5. Decorated photo frame 6 to 13 Medium 3Doodler Start+ Glues the pieces to the frame
6. Charm bracelet 6 to 13 Medium 3Doodler Start+ Checks the size against her wrist
7. Butterfly necklace 6 to 13 Medium 3Doodler Start+ Threads and ties the cord
8. Trinket dish 14 and up Long SCRIB3D P1 Tapes the bowl, stays in the room
9. Pen pot 14 and up Long SCRIB3D P1 Stays in the room, unplugs the pen
10. Daisy and sunflower bouquet 14 and up Long SCRIB3D P1 Sets up the pen, stays in the room

Ten Mother’s Day gifts, from easiest to most ambitious

Easy: flat gifts for ages 6 to 13

All four are flat pieces traced from a template, and the fill hides a wobbly line. The child draws; the adult handles anything involving scissors, glue or metal.

1. Card with raised flowers. 3Doodler publishes a free Mother’s Day card stencil with a message and flowers, and allows about 20 minutes for it with its hot Create+ pen. The child traces the words and flowers, then lifts the petal tips while the plastic is still warm so they stand off the card. You need a blank card and a glue stick or double-sided tape. Steps below.

2. Bookmark. A long strip filled with lines that all run the same way, with a shape at the top; 3Doodler’s free library has a bookworm bookmark stencil. Keep it thin, one layer or two at most, so the book still closes. You need one main colour and a ruler.

3. Keyring tag with her initial. A filled letter or heart with a thick loop at the top, from 3Doodler’s custom keychain stencil or drawn freehand. Go round the loop twice so it can carry keys. You need two colours and a split ring.

4. Flower fridge magnet. A flat flower in two or three colours, filled so the colours fuse where they meet. The adult glues a small craft magnet to the back. A child who made snowflakes and hanging stars from our Christmas decoration ideas already knows this flat-fill technique.

Intermediate: joined pieces for confident Start+ users

These join several small pieces, so they take patience more than skill. 3Doodler’s joining method: add a little plastic at the corners where pieces meet, then draw along the whole joint. They suit children who have finished a few easy pieces, often from about 9 (our guide, not a maker rating).

5. Decorated photo frame. Four to six small hearts or butterflies fixed round a plain wooden frame that holds a photo of the two of you. 3Doodler’s library has pastel butterfly and geometric heart stencils. The child draws and arranges; the adult does the gluing. Steps below.

6. Charm bracelet. 3Doodler’s charm bracelet stencil suggests personalising it with shapes that mean something: her initial, the family pet, her favourite flower. Draw each charm thick enough to survive being worn. The adult checks the length against a bracelet she already wears.

7. Butterfly necklace. Three small butterflies hanging from a cord, from 3Doodler’s butterfly necklace stencil. Give each butterfly a solid loop so the cord can’t pull through. You need three colours and a length of cord.

Ambitious: curved and standing gifts for teenagers

These pieces curve or stand up, and they hold their shape best in PLA from a hot pen; the Start+ plastic stays softer than PLA. Under 14? Make the flowers flat on the Start+ and fix them to the card or frame instead.

8. Trinket dish for rings. Turn a small bowl upside down, wrap it in masking tape as 3Doodler advises for any mould, and draw a lattice over it with a solid rim. Ease it off once cool. Prusa advises against using PLA objects for food because their fine grooves can harbour bacteria, so this dish is for rings and earrings, not sweets.

9. Pen pot for her desk. A filled square base and four lattice panels of the same size, tacked at the corners and then welded along each joint. Draw the panels against a ruler, or the box won’t close square.

10. Daisy and sunflower bouquet. 3Doodler rates its daisy or sunflower tutorial as intermediate and allows 45 minutes for one flower with its hot pen, so a bunch of three to five fills an afternoon or two. You need yellow, white, brown and green, plus ribbon. Steps below.

What you need

A pen that matches the maker’s age

For under-tens, the Start+ is the pen we’d choose. It’s rechargeable, has a stand-by mode, and according to 3Doodler UK comes with a charging cable, 72 strands of Start eco-filament and an activity guide. It takes only 3Doodler Start plastic or a compatible 2.5 mm pack, so standard 1.75 mm PLA won’t fit. Charge it the night before.

3Doodler Start+ Essentials 3D Pen Set
Our pick for under-tens
3Doodler Start+ Essentials 3D Pen Set

3Doodler says it has no external hot parts and designs it for ages 6 to 13, so a young child can make the first seven gifts with it.

Check price on Amazon Price shown on Amazon

For teenagers, the SCRIB3D P1 takes 1.75 mm PLA and ABS and has a stepless speed slider and a ceramic nozzle. Stick to PLA for gifts: ABS needs the higher temperature setting and a well-ventilated room. Other options are on our shelf of 3D pens for kids.

SCRIB3D P1 3D Pen with Display
Our pick for teenagers
SCRIB3D P1 3D Pen with Display

Published PLA settings of 160–210 °C and a stepless speed slider for the curved and standing gifts. SCRIB3D’s product page rates it for ages 14 and up; its manual says adult use only.

Check price on Amazon Price shown on Amazon

A mat, templates and odds and ends

The AQTAQ 3D Pen Starter Kit suits a household making several gifts: its transparent board is made for tracing stencils, which is how most of these gifts start. It comes without a pen, and its PLA fits the P1, not the Start+. You also need a heat-rated silicone mat (the kit has one), a blank card, glue, double-sided tape, masking tape, a ruler, split rings, craft magnets, cord, a plain frame and ribbon.

If the pen is new, try two or three of our beginner projects in learning order the weekend before.

Who does what with a hot pen

The P1’s nozzle and freshly drawn plastic are hot. The adult sets the pen up on a heat-rated mat, stays in the room while the teenager draws, and unplugs it at the end. Follow each maker’s age rating, keep drinks off the mat and let pieces cool before anyone handles them. Burns, fumes and house rules are covered in our guide to 3D pen safety for children.

Step outlines for three of the gifts

Card with raised flowers

  1. Print 3Doodler’s free Mother’s Day card stencil and lay it under a clear sheet on your mat.
  2. Trace the words in one colour.
  3. Trace the flowers, switching colours for petals and leaves.
  4. While the plastic is still warm, lift each petal tip slightly so it stands out.
  5. Let everything cool, then peel the pieces off.
  6. Fix the flat side of each piece to the card with a glue stick or double-sided tape, and press until it holds.

Decorated photo frame

  1. Choose a plain frame and a photo of the child with their mum.
  2. Trace four to six hearts or butterflies, fill each one, and peel them off once cool.
  3. Lay them round the frame until the child likes the arrangement.
  4. The adult glues each piece in place.
  5. Leave the glue to dry fully before the photo goes in.

Daisy and sunflower bouquet

  1. Print 3Doodler’s daisy or sunflower stencil and trace every petal.
  2. Peel each petal off, add a layer of plastic to its back and curve it gently.
  3. Draw a circle for the centre, add plastic to its edge and attach the petals one at a time.
  4. Fill the centre with more plastic to lock the petals in.
  5. Trace two green shapes, one large and one small, and fix them to the back as a base.
  6. Trace a green stem, add plastic to one end and attach it to the base.
  7. Repeat in other colours, then tie the stems together with ribbon.

When should you start?

Start two weekends before Mothering Sunday: one for a practice piece, one for the gift. Make anything fragile, like the bouquet or the necklace, first, so there is time to redo a petal or a loop. February half-term usually comes first, and a few half-term activities with the pen make a good warm-up. Store finished pieces flat in a box until the day.

Common questions


Can a 3D pen make a coaster for hot drinks?

Not for hot drinks. Prusa says PLA gets soft and deforms above 60 °C, so a mug of freshly made tea could soften and warp it, and the Start+ plastic stays softer than PLA. A coaster for cold drinks works, or make the trinket dish instead.


Can a younger child use the SCRIB3D P1 if an adult helps?

SCRIB3D’s product page rates the P1 14+, and its manual says adult use only, so it isn’t for younger children even with help. Instead, 3Doodler designs the 3Doodler Start+ for ages 6 to 13 and says it has no external hot parts.


Will 3D pen flowers last on a sunny windowsill?

They need no water, but Prusa notes that PLA degrades under UV light, so strong sun shortens its life. A shelf or table out of direct sunlight keeps a bouquet looking fresh for longer.


Does the AQTAQ filament fit the 3Doodler Start+?

No. The AQTAQ kit’s PLA is 1.75 mm for hot pens, while the Start+ takes only 3Doodler Start plastic or a compatible 2.5 mm pack. The kit’s mat, templates and finger guards still work alongside any pen.


Sources

The 3D Hub editorial team

We compare 3D pens and printers on the specifications their makers publish, and say plainly when a manufacturer doesn't publish a figure. We don't accept payment for placement, and no ranking here moves because of a commission rate.