The best stocking fillers for a child with a 3D pen are small things that keep the pen in use: a refill pack that fits their pen, a silicone mat with stencils, a hard case and a printed template pack. Check the refill first: most pens take 1.75 mm PLA, but the 3Doodler Start+ takes its own strands.
Everything below fits in a stocking. The ideas come first, then a table of which refill fits which pen, so nothing ends up in the wrong drawer on Boxing Day.
Stocking filler ideas for 3D pen fans
1. A refill pack that fits their pen
Refills run out faster than children expect, so this is the one filler that always gets used. For pens that take 1.75 mm PLA, the SCRIB3D PLA Refills give 20 colours of about 4.9 m each, around 100 m in all, with each colour vacuum packed. SCRIB3D says they fit its own pens, PIKA3D, MYNT3D and most pens that take 1.75 mm PLA, but not the 3Doodler Create+.
For a 3Doodler Start+, buy refills made for it. 3Doodler’s own Start plastic is the safe default, because 3Doodler says the use of third-party filament will void any active warranty on the Start+. You’ll find both kinds in our 3D pen refills and filament range.

Twenty vacuum-packed colours, about 100 m in total, for most pens that take 1.75 mm PLA.
2. A big colour palette
Some children care more about colours than metres. The Yungden 30-Colour PLA Refills include 24 standard shades, 2 transparent and 4 fluorescent, at 3 m each. That length suits outlines and details; for a big solid model, one colour in bulk goes further. Like all 1.75 mm PLA, it won’t fit the 3Doodler Start or low-temperature pens.
3. Glow-in-the-dark strands for a Start+
Owners of a 3Doodler Start+ can have special colours too. The Kretrum 32-Colour Refills for 3Doodler Start include glow-in-the-dark strands, 15 cm each, in a resealable pack. The seller says they fit the 3Doodler Start and Start+ only. They’re third-party, so keep 3Doodler’s warranty note in mind if the pen is still covered.
4. A silicone mat with stencils
A heat-resistant mat protects the table and makes lines easy to peel off. The AQTAQ 3D Pen Starter Kit pairs a 45 × 28 cm silicone mat rated 220–260 °C with 40 templates on 20 double-sided sheets, a transparent drawing board, four finger guards and 50 m of 1.75 mm PLA. The pen itself isn’t included.
A heat-rated mat, 40 templates and four finger guards, with 50 m of PLA to start drawing straight away.
5. A refill kit with everything but the pen
If the stocking has room for one bigger parcel, the 3Dmate PLA Refill Kit bundles about 110 m of 1.75 mm PLA in standard, transparent, metallic and fluorescent shades with a silicone mat, a stencil book and four finger guards. It suits a child who got a 1.75 mm pen on their birthday and has used up the starter filament.
6. A hard case
A case keeps the pen, refills and nozzle tools together and out of reach of younger siblings. The Lebakort Hard Case has a nylon-over-EVA shell, a soft lining, mesh pockets and a zip with a wrist strap. The seller lists the SCRIB3D P1, MYNT3D Super and PIKA3D Pro as fits, and pens of similar size. For any other pen, measure its length before ordering. Let the nozzle cool for five minutes before packing the pen away.

A zipped hard case with mesh pockets for refills, sold to fit the SCRIB3D P1 and MYNT3D Super.
7. A printed template pack
Print a handful of our free printable 3D pen templates, slip them into a plastic wallet and roll it up with a ribbon. Pick a theme they love, such as animals, letters or vehicles. Templates give a child a clear first project for Christmas afternoon.
8. Challenge cards
Write six to ten cards, each with one small challenge: “a spider with eight legs”, “your initials, standing up”, “something that floats”. Add a rule or two, such as one colour only or ten minutes on the clock. They cost nothing and turn a quiet afternoon into a game.
9. A project jar
Fill a clean jar with folded slips of paper, each naming a project. On a rainy day, the child picks one and makes it. Mix easy ones with a few harder builds. For festive slips, borrow from our Christmas decoration ideas for 3D pens, from snowflakes to tree toppers.
Which refill fits which pen?
This is the one thing to get right. Two plastics don’t swap: 1.75 mm PLA for standard hot pens, and low-temperature strands for the 3Doodler Start family. The table uses the makers’ and sellers’ own compatibility statements.
| Refill | Fits | Does not fit |
|---|---|---|
| SCRIB3D PLA Refills (1.75 mm PLA) | SCRIB3D, PIKA3D, MYNT3D and most 1.75 mm PLA pens, according to SCRIB3D | 3Doodler Create+ (SCRIB3D), 3Doodler Start and Start+ |
| Yungden 30-Colour PLA Refills (1.75 mm PLA) | Standard hot 3D pens | 3Doodler Start, low-temperature PCL pens |
| Kretrum 12-Colour PLA Refills (1.75 mm PLA) | Most pens and printers that take 1.75 mm filament | 3Doodler Start and Start+ |
| 3Dmate PLA Refill Kit and AQTAQ 3D Pen Starter Kit (1.75 mm PLA) | Pens that take 1.75 mm PLA | 3Doodler Start+ (it takes Start plastic only) |
| Kretrum 32-Colour Refills for 3Doodler Start (PCL, about 2.5 mm) | 3Doodler Start and Start+ only, according to the seller | Every 1.75 mm pen |
Among the pens we list, the SCRIB3D P1, MYNT3D Super, 3Doodler Flow and LIHUACHEN RPC200B 3D Pen (Button Version) take 1.75 mm filament. For the Flow, 3Doodler says it can’t guarantee the quality, safety or compatibility of any third-party filament, so its own refills are the cautious choice. The 3Doodler Start+ takes 3Doodler Start plastic or a pack made for it.
Ages matter for the pen, not just the refills. 3Doodler designs the Start+ for children aged 6 to 13, LIHUACHEN rates its RPC200B for ages 7 and over, and SCRIB3D’s product page gives 14+ for the P1. If you’re still choosing the pen itself, our 3D pen gift guide by age sets out which suits whom.
How to wrap a 3D pen stocking kit
A few loose bits become one proper present when they arrive together. Here’s a simple way to build it.
- Choose a zip bag or small box as the “kit” container.
- Put in one refill pack that fits their pen; check the table above.
- Add a mat or a few stencils, rolled with a ribbon.
- Add three challenge cards and one printed template.
- Write a label with the pen’s name on it, so the refills never get mixed up with a sibling’s.
- Put the kit at the top of the stocking, so it’s found before the chocolate.
Keep loose strands, finger guards and small parts away from toddlers in the house.
Common questions
Do all 3D pen refills fit all pens?
No. Most hot pens take 1.75 mm PLA, while the 3Doodler Start and Start+ take their own low-temperature strands. Some 1.75 mm packs also exclude particular pens, so check the maker’s compatibility list before you buy.
Can I use other brands of refill in a 3Doodler Start+?
Packs sold for the Start exist, but 3Doodler says the use of third-party filament will void any active warranty on the Start+. If the pen is still under warranty, 3Doodler’s own Start plastic is the safer choice.
How much refill should I put in a stocking?
One pack is plenty for a stocking. Packs vary from 3 m per colour to around 5 m, so compare the total length rather than the number of colours if the child makes big models.
What can I give a child who has a 3D pen but no ideas?
Printed templates, challenge cards or a project jar give them something to make on the day. Pair one of these with a refill pack and they have both the idea and the plastic.