Troubleshooting

Resin Prints Failing or Not Sticking: Fixes in Order

Cold resin, a plate too far from the film, short bottom exposure, a worn film or missing supports: how to tell which one, and the fixes in order.

Resin Prints Failing or Not Sticking: Fixes in Order
Heads up: we research and compare the products we recommend, and we only link to gear we would consider buying ourselves. When you buy through links on this page we may earn a commission, at no extra cost to you. As an Amazon Associate we earn from qualifying purchases.
On this page
  1. Try this first: clear the vat and read the failure
  2. Why won't a resin print stick? Causes, in the order to check them
  3. When to replace a part instead
  4. Common questions
  5. Sources
Short answer

A resin print that won’t stick to the build plate usually means cold resin, too big a gap between plate and film, or too little bottom exposure. Clear the vat, warm the resin, check the gap, then add bottom exposure. If the base holds but the model fails, check the release film, then supports and orientation.

You come back to an empty build plate and a cured sheet stuck to the film at the bottom of the vat. Or the base held, and the model came away halfway up. For both, Anycubic’s and Elegoo’s own troubleshooting pages point to the same short list of causes. This guide stops when the print is off the plate; our guide to washing and curing your prints takes it from there.

Try this first: clear the vat and read the failure

Where the resin ended up tells you where to look.

What you see Likely cause Go to
Nothing on the plate and nothing cured in the vat The screen isn’t exposing Step 3 below
Nothing on the plate, a cured sheet on the film The base never gripped: cold resin, too big a gap or too little bottom exposure Causes 1 to 3
Base on the plate, model missing or broken off partway Cold resin, exposure or lift settings, unsupported parts Causes 1, 3 and 5
Failures only near the edges of the plate Levelling, a worn film or a dim patch of screen Causes 2 and 4, then the screen check

Then run this routine, in order. Read up on handling resin safely at home before your first clean-up.

Uncured resin irritates skin and can cause an allergy: wear nitrile gloves, work in a ventilated room and keep the printer out of bedrooms and living spaces. During an exposure test, don’t look directly at the screen: Anycubic warns it can injure your eyes.

  1. Stop the print, put on nitrile gloves and take the build plate off.
  2. Lift any cured sheet or flakes out of the vat without scratching the film. Elegoo suggests filtering the resin through a funnel before you use it again.
  3. If nothing cured at all, run the exposure test with plain paper on the screen instead of the vat (Tools, then Exposure Test, on the Photon Mono 4) and check that the image on the paper matches the one on the control screen.
  4. Check the temperature next to the printer (cause 1).
  5. Clean the build plate: Elegoo lists a contaminated plate among the causes.
  6. Print the test file from the printer’s USB drive before your own model. Anycubic suggests this to rule out a problem with the model’s supports.

Why won’t a resin print stick? Causes, in the order to check them

Usually because the first layers never cured firmly against the plate: the resin was too cold, the gap too large or the exposure too short. Unplug the printer and follow its manual before you remove anything other than the vat and plate.

1. The resin or the room is too cold

Symptom: the base peels off the plate, or supports and parts of the model break away. Why: Elegoo puts high resin viscosity first among its causes: thick resin flows back under the plate slowly and cures less well. The makers’ figures:

Temperature What the maker says
About 23 °C Anycubic’s best printing temperature for resin
25 °C Elegoo’s optimal printing temperature; below it, Elegoo suggests preheating the resin
10–20 °C Resin flows less and is harder to cure, so exposure must go up, according to Anycubic
Below 10 °C Resin won’t cure, according to Anycubic
30 °C What the Saturn 4 Ultra 16K’s tank heating holds the resin at, according to Elegoo

Fix: warm the room, or move the printer to a warmer one. Below 25 °C, Elegoo suggests standing the resin bottle in warm water at about 60 °C for around ten minutes, and switching on any tank heater in advance.

If your printer lives somewhere cool, the Elegoo Saturn 4 Ultra 16K heats its own vat: switch on Tank Heating (Settings, then Accessibility features) and it warms the resin to 30 °C before printing, according to Elegoo.

Elegoo Saturn 4 Ultra 16K Resin 3D Printer
Our pick for a cold room
Elegoo Saturn 4 Ultra 16K Resin 3D Printer

A heated vat and automatic levelling help with two of the usual causes, and its AI camera flags a detached print, according to Elegoo.

Check price on Amazon Price shown on Amazon

2. The plate sits too far from the film

Symptom: nothing on the plate and a cured sheet on the film, or one side failing while the other prints. Why: Anycubic explains that if the gap between the plate’s zero position and the release film is too large, the resin can’t stick to the plate. Fix: check the gap. Anycubic’s routine for the Anycubic Photon Mono 4:

  1. Remove the vat and clean the build plate.
  2. Lay levelling paper or A4 paper on the left side of the screen.
  3. Choose Tools, then Move Z-axis, and let the plate come down. Don’t pull the paper while it settles.
  4. Pull the paper and feel the resistance, then repeat on the right side.
  5. If one side pulls noticeably more easily, level the plate again with Anycubic’s video.

Anycubic says the Photon Mono 4’s four-point levelling is needed once, so treat this as a check. The Saturn levels itself; if it reports a levelling fault, follow Elegoo’s manual.

3. Bottom exposure is too short, or the lift too harsh

Symptom: a thin, soft sheet left on the film, or a base that holds while the model tears away above it. Why: with too little bottom exposure or too few bottom layers, the base doesn’t cure firmly enough. Fix: Anycubic suggests adding 10 seconds of bottom exposure and five bottom layers to your settings; Elegoo suggests 5–10 extra seconds for bottom layers and 1–3 for normal layers. Larger, heavier models need a more solid base, Anycubic adds.

On the Photon Mono 4 with Anycubic resin, if the test file doesn’t form on the plate, Anycubic says to try 80 seconds of bottom exposure; if only the base sticks, raise the normal exposure instead.

Check the lift too. Anycubic warns that too fast a lift pulls hard enough to crack or break the model, so keep the slicer’s default; too short a lift leaves the new layer stuck to the film. Elegoo also suggests a longer light-off delay and, on lift-type machines, 2–3 mm more lift height.

New resin means new settings. If you switch, for example to the Elegoo Water Washable Resin 2.0, ask the resin maker for its recommended settings. On the Photon Mono 4, Anycubic’s R_E_R_F test file on the USB drive helps you find the right exposure.

4. The release film is worn, cloudy or slack

Symptom: prints fail in one area, often near the edges, where they used to succeed. Why: Elegoo lists ageing, whitening or damage of the release film among the causes. Anycubic adds that a loose film, usually after a home replacement, leaves the gap too large. Fix: empty and clean the vat, then look at the film against the light for white patches or scratches. Replace a damaged film promptly, and tighten the film screws if it’s slack.

5. Supports, islands and orientation

Symptom: the base and supports print, but parts of the model are missing or loose in the vat. Why: a part with nothing under it prints into thin air. Fix: run your slicer’s island check. In Anycubic Photon Workshop, green means supported, yellow may need supports and red must have them.

Hollow models add suction: Anycubic says a hollow interior creates a vacuum that can pull the model onto the film, so punch two holes, one near the plate and one higher up. Hollowing also shrinks each layer, which Anycubic says lowers the pulling force and helps stop the base peeling. Orientation works the same way: angle a big flat face so each layer is a smaller slice.

When to replace a part instead

Replace the release film once it’s whitened, scratched or damaged. Suspect the screen when failures start suddenly and you haven’t changed settings, resin or room. Elegoo’s check: remove the vat, lay white paper over the screen, run a full-screen exposure and look for clearly darker patches, especially where prints fail. If you find them, Elegoo says the LCD must be replaced: contact the maker’s support, and follow its manual for anything that involves removing parts.

If the printer itself is the weak point, a model that heats its vat and levels itself helps with two of the five causes. See our Saturn versus Photon Mono 4 comparison, or browse our mid-range and resin printers.

Common questions


Why is my resin print stuck to the FEP film instead of the build plate?

The first layers bonded to the film more firmly than to the plate. Anycubic’s usual suspects are too large a gap at the zero position, too little bottom exposure or too few bottom layers, and cold resin. Check the gap, warm the resin, then add bottom exposure.


What temperature should resin be for printing?

Anycubic gives about 23 °C and Elegoo 25 °C. Between 10 and 20 °C, Anycubic says resin flows less and needs more exposure; below 10 °C it won’t cure. Warm the room or the bottle, or use a printer that heats its vat.


How much should I increase bottom exposure?

Anycubic suggests adding 10 seconds and five bottom layers; Elegoo suggests 5–10 seconds more. Bigger, heavier models need a firmer base. Change one setting at a time so you know what fixed it.


Sources

The 3D Hub editorial team

We compare 3D pens and printers on the specifications their makers publish, and say plainly when a manufacturer doesn't publish a figure. We don't accept payment for placement, and no ranking here moves because of a commission rate.